1600 Lumen Trionic LED Front Light with Battery Pack

This manual both shows how you attach the light holder and the light on a Walker (left column below) and also how you attach them on a Veloped (right column below).

In the left-hand photo, A shows the holder attachment parts for a Walker (2 screws + 2 washers). B shows the holder attachment parts for a Veloped (1 screw + 1 knurled nut + 1 nut).

1600 Lumen Trionic LED Front Light with Battery Pack

Attaching the Light Holder

Instructions for a Walker

On top of the black semi-vertical tube, locate the two screws that clamp the grip tube, situated in front of the brake lever.
A1. On top of the black semi-vertical tube, locate the two screws that clamp the grip tube, situated in front of the brake lever.
Loosen both screws with the 5mm allen key included with the LED light.
A2. Loosen both screws with the 5mm allen key included with the LED light.
Remove the two screws from the grip clamp.
A3. Remove the two screws from the grip clamp.
Place the light holder on top of the grip clamp, with its circular and slotted light attachment pointing forwards and upwards. Enter the two screws with washers into the holes of the clamp.
A4. Place the light holder on top of the grip clamp, with its circular and slotted light attachment pointing forwards and upwards. Enter the two screws with washers into the holes of the clamp.
Tighten the two screws with the 5mm allen key. NOTE: It is important that you tighten the screws properly as they secure the grip tube with its rubber grip and brake lever.
A5. Tighten the two screws with the 5mm allen key. NOTE: It is important that you tighten the screws properly as they secure the grip tube with its rubber grip and brake lever.

Instructions for a Veloped

Locate the screw at the center folding hinge of the U-shaped grip bar of the Veloped. Unscrew the screw with the included 4mm allen key and remove it.
A1. Locate the screw at the center folding hinge of the U-shaped grip bar of the Veloped. Unscrew the screw with the included 4mm allen key and remove it.
Replace the old screw with the longer screw included with the LED light. Attach the longer screw to the hinge and tighten it with the 4mm allen key.
B2. Replace the old screw with the longer screw included with the LED light. Attach the longer screw to the hinge and tighten it with the 4mm allen key.
Attach the short angled end of the light holder to the lower end of the screw, on the downside of the grip bar. Fasten the holder with one washer and the knurled nut.
B3. Attach the short angled end of the light holder to the lower end of the screw, on the downside of the grip bar. Fasten the holder with one washer and the knurled nut.
For a more secure holder attachment, avoiding the holder to unintentionally turn sideways, replace the knurled nut with the included stainless steel nut and tighten it with a 10mm spanner.
B4. For a more secure holder attachment, avoiding the holder to unintentionally turn sideways, replace the knurled nut with the included stainless steel nut and tighten it with a 10mm spanner.
This photo shows the light holder as correctly attached.
B5. This photo shows the light holder as correctly attached.

Attaching the LED Light to the Holder

Instructions for a Walker

Identify the circular front end of the light holder, with two slots for attaching the light.
A6. Identify the circular front end of the light holder, with two slots for attaching the light.
Push the slotted bracket of the light into the slots of the holder and make sure they are aligned. Seen in the traveling direction of the Walker, enter the included wingnut from the left and tighten it.
A7. Push the slotted bracket of the light into the slots of the holder and make sure they are aligned. Seen in the traveling direction of the Walker, enter the included wingnut from the left and tighten it.

Instructions for a Veloped

Locate the screw at the center folding hinge of the U-shaped grip bar of the Veloped. Unscrew the screw with the included 4mm allen key and remove it.
B6. Locate the screw at the center folding hinge of the U-shaped grip bar of the Veloped. Unscrew the screw with the included 4mm allen key and remove it.
Identify the circular front end of the light holder, with two slots for attaching the light.
B7. Identify the circular front end of the light holder, with two slots for attaching the light.

Placing the Battery Pack

Instructions for a Walker

Run the longer extension cable along the semi-vertical grip tube of the Walker and secure it with the included velcro strap.
A8. Run the longer extension cable along the semi-vertical grip tube of the Walker and secure it with the included velcro strap.
You can cut the excessive length of the velcro strap with a pair of scissors.
A9. You can cut the excessive length of the velcro strap with a pair of scissors.
Place the battery pack in the rear zippered pocket of the basket.
A10. Place the battery pack in the rear zippered pocket of the basket.

Instructions for a Veloped

Run the longer extension cable along the U-shaped grip bar of the Veloped and secure it with the included velcro strap.
B8. Run the longer extension cable along the U-shaped grip bar of the Veloped and secure it with the included velcro strap.
You can cut the excessive length of the velcro strap with a pair of scissors.
B9. You can cut the excessive length of the velcro strap with a pair of scissors.
Place the battery pack in the rear zippered pocket of the basket.
B10. Place the battery pack in the rear zippered pocket of the basket.

The package contains

The package contains

How to operate the light

How to operate the light

Product Reviews    

  • 5 0

    Simply AMAZING…

    I ordered it last weekend, and the Veloped arrived on Wednesday. It's very easy to assemble. And most importantly, it's a joy to ride over rough terrain. My husband and I immediately chose a challenging route: cobblestones, grass, fields, roots. No p…

    Read the Full Review 
  • 1 8

    Simply brilliant!…

    The Veloped Trek works perfectly. It rides over hill and dale. Snow and ice are no problem either. It's a bit bulky, but the main thing is that it handles the terrain. My dog ​​is also thrilled that Mrs. Hen can walk again.…

  • 1 1

    Finally more freedom of movement and safety…

    After several health challenges, I find walking difficult, especially on uneven surfaces. I hardly ever went outside anymore. I particularly missed walking in the woods. Now my family has ordered me the Veloped Sport. At last I can go for a walk out…

    Read the Full Review 
  • 3 1

    Wheel hub cap…

    Easy to order, everything worked out great…

  • 9 14

    The Walker allows me to walk……

    The Walker allows me to walk on paths as well as safely cross lawns without the help of other people. The usage is possible without bending your wrists. There is very positive feedback from other people regarding the bright red color.
    Only the right…

    Read the Full Review 
    Trustpilot
  • 10 4

    Brilliant!…

    I have MND and walking has become more difficult - mainly due to the worry of tripping and balance. Since I have had the walker, I have been able to enjoy going for walks again and can walk much faster with the walker for support. The walker is so …

    Read the Full Review 
    Trionic
  • 12 4

    Getting back into the garden…

    The Veloped Trek has allowed me to get back into the garden, see the plants, even prune an overgrown bush, hang out washing (exciting) and just experience my large backyard again.

    MS limits me in many ways, so the ability to safely walk on grass …

    Read the Full Review 
    Trustpilot
  • 11 4

    Veloped Tour 14er M…

    Very satisfied. Thank you!…

  • 12 11

    Ladies and gentlemen……

    Ladies and gentlemen, I am very satisfied with my Veloped, it has fulfilled all my wishes. No extreme conditions in the mountains and big obstacles could stop me.
    The seat is not optimal because the arch is not round and too hard.…

    Trustpilot

Subscribe to our newsletter!