1000 Lumen Trionic LED Front Light

This manual both shows how you attach the light holder and the light on a Walker (left column below) and also how you attach them on a Veloped (right column below).

In the left-hand photo, A shows the holder attachment parts for a Walker (2 screws + 2 washers). B shows the holder attachment parts for a Veloped (1 screw + 1 knurled nut + 1 nut).

1000 Lumen Trionic LED Front Light

Attaching the Light Holder

Instructions for a Walker

On top of the black semi-vertical tube, locate the two screws that clamp the grip tube, situated in front of the brake lever.
A1. On top of the black semi-vertical tube, locate the two screws that clamp the grip tube, situated in front of the brake lever.
Loosen both screws with the 5mm allen key included with the LED light.
A2. Loosen both screws with the 5mm allen key included with the LED light.
Remove the two screws from the grip clamp.
A3. Remove the two screws from the grip clamp.
Place the light holder on top of the grip clamp, with its circular and slotted light attachment pointing forwards and upwards. Enter the two screws with washers into the holes of the clamp.
A4. Place the light holder on top of the grip clamp, with its circular and slotted light attachment pointing forwards and upwards. Enter the two screws with washers into the holes of the clamp.
Tighten the two screws with the 5mm allen key. NOTE: It is important that you tighten the screws properly as they secure the grip tube with its rubber grip and brake lever.
A5. Tighten the two screws with the 5mm allen key. NOTE: It is important that you tighten the screws properly as they secure the grip tube with its rubber grip and brake lever.

Instructions for a Trionic Veloped

Locate the screw at the center folding hinge of the U-shaped grip bar of the Veloped. Unscrew the screw with the included 4mm allen key and remove it.
A1. Locate the screw at the center folding hinge of the U-shaped grip bar of the Veloped. Unscrew the screw with the included 4mm allen key and remove it.
Replace the old screw with the longer screw included with the LED light. Attach the longer screw to the hinge and tighten it with the 4mm allen key.
B2. Replace the old screw with the longer screw included with the LED light. Attach the longer screw to the hinge and tighten it with the 4mm allen key.
Attach the short angled end of the light holder to the lower end of the screw, on the downside of the grip bar. Fasten the holder with one washer and the knurled nut.
B3. Attach the short angled end of the light holder to the lower end of the screw, on the downside of the grip bar. Fasten the holder with one washer and the knurled nut.
For a more secure holder attachment, avoiding the holder to unintentionally turn sideways, replace the knurled nut with the included stainless steel nut and tighten it with a 10mm spanner.
B4. For a more secure holder attachment, avoiding the holder to unintentionally turn sideways, replace the knurled nut with the included stainless steel nut and tighten it with a 10mm spanner.
This photo shows the light holder as correctly attached.
B5. This photo shows the light holder as correctly attached.

Attaching the LED Light to the Holder

Instructions for a Walker

Identify the circular front end of the light holder, with two slots for attaching the light.
A6. Identify the circular front end of the light holder, with two slots for attaching the light.
Push the slotted bracket of the light into the slots of the holder and make sure they are aligned. Seen in the traveling direction of the Walker, enter the included wingnut from the left and tighten it.
A7. Push the slotted bracket of the light into the slots of the holder and make sure they are aligned. Seen in the traveling direction of the Walker, enter the included wingnut from the left and tighten it.

Instructions for a Trionic Veloped

Locate the screw at the center folding hinge of the U-shaped grip bar of the Veloped. Unscrew the screw with the included 4mm allen key and remove it.
B6. Locate the screw at the center folding hinge of the U-shaped grip bar of the Veloped. Unscrew the screw with the included 4mm allen key and remove it.
Identify the circular front end of the light holder, with two slots for attaching the light.
B7. Identify the circular front end of the light holder, with two slots for attaching the light.

Instructions for Use

Overview

Overview

Caution

It is normal for the battery to reach a high temperature (up to 104°F / 40°C) during charging due to chemical reactions within the battery. The battery may also become warm if it is not fully drained before charging. Several factors can affect the battery's lifespan, including the type of cell, usage strain, maintenance routine, temperature, and the number of charge cycles. Generally, a higher battery capacity results in a longer operation time. The battery capacity may decrease to approximately 80% of its original capacity after 300–500 charge/discharge cycles. With proper care, the battery can have a lifespan of up to 3 years. Water resistant is for rain water only. Do not submerge the bat- tery or the whole light into water when cleaning. Clean the light with a soft damp cloth when needed."

Battery Performance

Battery performance is significantly affected by temperature variations:

•Low Temperature: At 0°C, capacity decreases by 5–10%, reducing operation time by 50%. At -20°C, capacity drops by 30%, potentially shortening operation time by 70%. Performance returns to normal when the temperature rises to 20°C.

•Self-Discharge Rate: At room temperature, the battery loses about 1% of its capacity per day. When stored at 40°C, the self-discharge rate increases, leading to a loss of approximately 5% of capacity per day.

To maintain optimal battery performance, avoid exposing it to extreme temperatures and store it in a cool, dry place.

If you do not use the battery for a long time be sure to recharge the battery every 3 months.

Safe Mode

When the battery is low, the light will automatically switch to a 50-lumen high-beam safe mode, providing an additional 30 minutes of operation.

How to operate the light

Press and hold the switch for 2 seconds to turn the light on or off. Click once to cycle through modes, and double-click to enable ultra-bright mode (1000 lm).

Press and hold the switch for 2 seconds to turn the light on or off. Click once to cycle through modes, and double-click to enable ultra-bright mode (1000 lm).

The package contains

Press and hold the switch for 2 seconds to turn the light on or off. Click once to cycle through modes, and double-click to enable ultra-bright mode (1000 lm).

Charging And Powerbank

Press and hold the switch for 2 seconds to turn the light on or off. Click once to cycle through modes, and double-click to enable ultra-bright mode (1000 lm).

Product Reviews    

  • 11 8

    Overall, I am satisfied.…

    I am 86-year-old and weigh 58 kg.
    The device looks good (to be envious), is well thought out and easy to assemble. What struck me:
    The heavy strain on the arm muscles
    - on uneven forest paths,
    - on inclines (effort needed to push uphill and to h…

    Read the Full Review 
    Trionic
  • 0 0

    My Trionic has changed my life!…

    My Trionic has changed my life.

    I love the outdoors, and a recent holiday to Dorset meant that i could walk places with my partner that I've not been able to access in years, because of my arthritis, and other walkers were not up to the job. The …

    Read the Full Review 
  • 12 1

    I am delighted with my Sport…

    The machine is exactly as described in the literature and on the website. It's really solid and stands up to life on a livestock farm. I doesn't often get on tarmac, it's mostly used on rough fields, farm yards and rough cart tracks. It worked perfec…

    Read the Full Review 
  • 4 1

    Very satisfied…

    The Walker 12er is fantastic. Since 2008 I have only moved around with a wheelchair because I could not use the health insurance walkers due to balance problems. With the Walker I bought from you I feel completely comfortable. I feel very confident w…

    Read the Full Review 
  • 17 17

    The neighbors all love it…

    The Rollator arrived in perfect condition, all I had to do was take it out of the box and start using it. It meets all of my expectations, the neighbors all love it. John…

    Trionic
  • 13 12

    Congratulations to the whole Trionic team!…

    What you have come up with is truly impressive. I can only recommend this walker! A few weeks ago I had an accident where my mobility has been compromised. Since I didn’t want to miss small hikes, I was looking for a stable walker. The Veloped Trek d…

    Read the Full Review 
    Trustpilot
  • 11 9

    Becoming Independent…

    I bought my Veloped in July 2021 and I have never looked back. Having suffered with a back and balance problem for several years, walking with the Veloped keeps my back straight and I am no longer concerned about my balance as the frame gives me conf…

    Read the Full Review 
    Trustpilot
  • 9 3

    Truly superior…

    Our son is very happy with this high-quality rollator. The very good brakes in combination with the large pneumatic wheels give him much more safety than he had with previous rollators. The handles are also much better than on his former ones. The sy…

    Read the Full Review 
    Trionic
  • 11 19

    S U P E R !…

    The shipping and the delivery of our Veloped Trek M 14er was completed in 3 days!
    So, it was very fast!

    Our Veloped was carefully packed and, when we unpacked it, was not damaged! We did not have any problems with the assembly either! See video a…

    Read the Full Review 
    Trionic

Subscribe to our newsletter!

"> ?>